Free Download Pipe/Line Sizing For Chemical Process Engineers

Published 3/2023

MP4 | Video: h264, 1280x720 | Audio: AAC, 44.1 KHz

Language: English | Size: 964.51 MB | Duration: 2h 6m

The only course with the best background knowledge and practical sizing calculations considering liquid and gas flows

**Free Download**

**What you'll learn**

The difference between shear stress and pressure

Essential parameters of fluid flow (flow rate, velocity, pressure drop, etc.)

Average velocity importance and calculation

Calculation of gas density at different operating conditions

The difference between actual and standard flow rates based on the real gas considerations

How to determine friction factor through a pipe in a modern way

Pressure drop calculation via the pipe

How to calculate erosional-limit velocity for the pipeline

How to consider pressure drop criteria for line sizing

How to perform line sizing considering above points

**Requirements**

Theory, background and practical sides of fluid flow are discussed here. No requirements for all levels of learners.

**Description**

One regular factor in flow rate design is the calculation of pipe size. To diminish capital cost, some engineers may decrease the pipe size and increase the velocity.Optimizing the pipe size and velocity of the fluid not only improves the system efficiency but can also increase the service life. Some of the issues faced during increased velocity and undersized piping:High velocity in pipelines promotes corrosion/pitting; piping may be repaired or replaced sooner than expected.Abrasives and Erosion can cause premature failureSurge pressures due to water hammer cause more damages at higher speed.This course is mainly focused on pipeline sizing considering velocity and pressure drop criteria. However, before directly getting into this, some background information is desired to be provided. Course was taught by Process Engineer working in oil and gas field to the group of bachelor and master students. The main aspects discussed via the course are:Fluid flow essentialsShear stressPrimary parameters for fluid flowSignificance of average velocity in calculationsViscosityFluid flow typesFlow regimes and Reynolds numberDifference between gas and liquid flowContinuity equation for fluid flowCalculation of density for gasesStandard vs actual flow ratesDetermination of friction factor through a pipeLine sizing performed on a real case problemAbove points have clearly been discussed during the course. This training can be really helpful for students, engineers and even teachers aiming to deliver line sizing essentials from engineering point of view. By spending only 2 hours, you can really understand the whole topic and further do practical calculations. Course instructor does also provide the service of answering questions for all course participants for free.

**Overview**

Section 1: Introduction

Lecture 1 Fluid Flow Essentials - The State of Matter

Lecture 2 Fluid Flow Essentials - Driving Force for Fluid Flow

Lecture 3 Fluid Flow Essentials - Shear Stress

Lecture 4 Fluid Flow Parameters - Flow Rate

Lecture 5 Fluid Flow Parameters - Average Velocity

Lecture 6 Fluid Flow Parameters - Viscosity

Lecture 7 Fluid Flow Parameters - Types of Viscosity

Lecture 8 Fluid Flow Types

Lecture 9 Flow Regimes and Reynolds Number

Lecture 10 Difference between Gas and Liquid Flow

Lecture 11 Continuity Equation for Gas and Liquid Flow

Lecture 12 Theory: Calculation of Density for Gases

Lecture 13 Practice: Calculation of Density for Gases - Part 1

Lecture 14 Practice: Calculation of Density for Gases - Part 2

Lecture 15 Theory: Standard vs Actual Flow Rates

Lecture 16 Practice: Standard vs Actual Flow Rates - Part 1

Lecture 17 Practice: Standard vs Actual Flow Rates - Part 2

Lecture 18 Determination of Friction Factor through a Pipe

Lecture 19 Pressure Drop Calculation for Gas Lines

Lecture 20 Pressure Drop Calculation for Liquid Lines

Lecture 21 Real Case Line Sizing: Problem Description

Lecture 22 Real Case Line Sizing: Determination of Erosional Velocity

Lecture 23 Performing Line Sizing

Chemical Process Engineering Graduates or Undergraduates,Chemical Engineers,Process Engineers,Any Discipline Engineers aiming to learn essentials of pipe sizing

Homepage

`https://www.udemy.com/course/pipeline-sizing-for-chemical-process-engineers/`

**Buy Premium From My Links To Get Resumable Support,Max Speed & Support Me**

**Links are Interchangeable - Single Extraction**

```
```**We need your support!
Make a donation to help us stay online**
Bitcoin (BTC)
bc1q08g9d22cxkawsjlf8etuek2pc9n2a3hs4cdrld
Bitcoin Cash (BCH)
qqvwexzhvgauxq2apgc4j0ewvcak6hh6lsnzmvtkem
Ethereum (ETH)
0xb55513D2c91A6e3c497621644ec99e206CDaf239
Litecoin (LTC)
ltc1qt6g2trfv9tjs4qj68sqc4uf0ukvc9jpnsyt59u
USDT (ERC20)
0xb55513D2c91A6e3c497621644ec99e206CDaf239
USDT (TRC20)
TYdPNrz7v1P9riWBWZ317oBgJueheGjATm